slipsil installation
1

SLIPSIL Installation Steps

CSD Sealing Systems products are simple and effective with noteable ease of installation, making it easier to achieve an effective fire, gas and water-tight seal. See installation instructions for SLIPSIL Seals for Cable and Pipe Entries below.

SLIPSIL Sealing Plugs

Installation instructions for cable and pipe entries.

Click on a step to view a bigger version. (Use the arrows to scroll)

STEP 1

STEP 1

Before starting the installation, any dirt or oil residues should be removed from the conduit opening.

STEP 2

STEP 2

The inside wall should then be treated with CSD lubricant along a distance which approximately corresponds with the length of the sealing plug.

STEP 3

STEP 3

The inside surfaces of both segments of the sealing plug need to then be covered with CSD lubricant.

STEP 4

STEP 4

The segments of the sealing plug need to be treated with CSD lubricant on the outside. Ensure all surfaces are well lubricated.

STEP 5

STEP 5

Place both segments of the sealing plug around the ducted pipe and then push into the conduit opening as far as the first serration.

STEP 6

STEP 6

Push both segments of the sealing plug evenly by hand, serration by serration, further into the conduit opening. For some plugs at extreme tolerance, a wooden section and mallet may be required.

STEP 7

STEP 7

To satisfy certification requirements a plug should be installed at each end of the penetration (flanged edge flush against frame). Installing the second plug, air can become trapped inside the penetration. Use a lubricated screwdriver and carefully insert the end between the two plug segments to release the air. Repeat process if required and second plug is fully inserted.

STEP 1

STEP 1

Before starting the installation, any dirt or oil residues should be removed from the conduit opening.

STEP 2

STEP 2

The inside wall should then be treated with CSD lubricant along a distance which approximately corresponds with the length of the sealing plug.

STEP 3

STEP 3

The inside surfaces of both segments of the sealing plug need to then be covered with CSD lubricant.

STEP 4

STEP 4

The segments of the sealing plug need to be treated with CSD lubricant on the outside. Ensure all surfaces are well lubricated.

STEP 5

STEP 5

Place both segments of the sealing plug around the ducted pipe and then push into the conduit opening as far as the first serration.

STEP 6

STEP 6

Push both segments of the sealing plug evenly by hand, serration by serration, further into the conduit opening. For some plugs at extreme tolerance, a wooden section and mallet may be required.

STEP 7

STEP 7

To satisfy certification requirements a plug should be installed at each end of the penetration (flanged edge flush against frame). Installing the second plug, air can become trapped inside the penetration. Use a lubricated screwdriver and carefully insert the end between the two plug segments to release the air. Repeat process if required and second plug is fully inserted.

SLIPSIL Sealing Plugs

Additional installation instructions for use on plastic pipes up to 225mm

Click on a step to view a bigger version. (Use the arrows to scroll)

STEP 8

STEP 8

For plastic pipes, you must use an 80mm wide wrap of RISE FRR/EHF rubber between the SLIPSIL plugs. A pre-formed sleeve can be used for pipe sizes up to 44mm and wrap in 1m or 3m lengths for sizes above.

STEP 9

STEP 9

Once the wrap is inserted in to the centre of the penetration, the second SLIPSIL plug can be installed as before. This will create your fully certified plastic pipe SLIPSIL penetration.

STEP 8

STEP 8

For plastic pipes, you must use an 80mm wide wrap of RISE FRR/EHF rubber between the SLIPSIL plugs. A pre-formed sleeve can be used for pipe sizes up to 44mm and wrap in 1m or 3m lengths for sizes above.

STEP 9

STEP 9

Once the wrap is inserted in to the centre of the penetration, the second SLIPSIL plug can be installed as before. This will create your fully certified plastic pipe SLIPSIL penetration.

Customer Focused

At CSD, we understand that high-risk environments require the highest levels of safety, which is why we offer on site training and quality inspections.

CSD products have been extensively tested by all major worldwide classification societies and independent institutes, and are proven to ensure the highest standards of quality, safety, reliability and durability.

Please contact us for any further product information or to order a copy of our brochures.

Latest News

NOFIRNO Duct Seal

9th June 2017

CSD are committed to constantly innovating our products and services to meet the needs of our customers so we are proud to an ...

Read more

Customer testimonials

See more testimonials

"CSD's team are very focused in their approach to provide a high quality product and service. We are looking forward to working with them in the future."
Senior Electrical Design Engineer, Thames Water

© Copyright 2011 CSD Sealing Systems Limited

Legal Information - Terms and Conditions
Design by Boxmodel Website Designers